Configuration ⚙ Options
Product

Microlab

Regulated power supply · laboratory

Precision regulated power supply for test and laboratory environments. Clean, constant power, ideal for reliable measurements.

← Back to: regulated power supplies

Microlab range

The models in the range

Microlab
Microlab — regulated power supply
Microlab double
Microlab — dual version
Microlab MX
Microlab MX — displays, A.min preset counter, totalising / daily counter
Microlab MXD double voie
Microlab MXD — dual-channel version
Microlab MX touchscreen
Microlab MX — Smart Panel touchscreen
Datasheet

Technical specifications

Data taken from the Microlab DC datasheet. Manual or touchscreen interface, voltage & current regulation.

150 W → 6 000 WEnclosure & 19" rack2U / 3U form factorsWeight 3 → 18 kgOutput 0–10 V to 0–1500 V230 Vac single-phase / 400 Vac 3-phase
Dimensions, form factors & weight
ModelOutputMains inputFormatDimensions (W × D)Form factorWeight
Microlab MX 150W150 W230 Vac single-phaseEnclosure215 × 265 mm2U3 kg
MX 300W300 W230 Vac single-phaseEnclosure215 × 265 mm2U3 kg
MX 600W600 W230 Vac single-phaseEnclosure215 × 265 mm2U4 kg
MX 1200W1200 W230 Vac single-phase19" rack / enclosure19" × 275 mm2U7 kg
MX 1500W1500 W230 Vac single-phase19" rack / enclosure19" × 275 mm2U8 kg
MX 2400W2400 W230 Vac single-phase19" rack / enclosure19" × 380 mm2U9 kg
MX 3000W3000 W230 Vac single-phase19" rack / enclosure19" × 380 mm2U14 kg
MX 4000W4000 W400 Vac 3-phase19" rack / enclosure19" × 380 mm3U15 kg
MX 5000W5000 W400 Vac 3-phase19" rack / enclosure19" × 380 mm3U16 kg
MX 6000W6000 W400 Vac 3-phase19" rack / enclosure19" × 380 mm3U18 kg
Output voltage / current — MX 150W · 300W · 600W
Output voltageMX 150WMX 300WMX 600W
0 – 10 V0 – 15 A0 – 30 A0 – 50 A
0 – 20 V0 – 7,5 A0 – 15 A0 – 30 A
0 – 30 V0 – 5 A0 – 10 A0 – 20 A
0 – 40 V0 – 4 A0 – 7,5 A0 – 15 A
0 – 60 V0 – 2,5 A0 – 5 A0 – 10 A
0 – 80 V0 – 2 A0 – 4 A0 – 8 A
0 – 120 V0 – 1,5 A0 – 2,5 A0 – 5 A
0 – 150 V0 – 1 A0 – 2 A0 – 4 A
0 – 200 V0 – 0,75 A0 – 1,5 A0 – 3 A
0 – 300 V0 – 0,5 A0 – 1 A0 – 2 A
0 – 600 V0 – 0,25 A0 – 0,5 A0 – 1 A
0 – 1200 V0 – 0,125 A0 – 0,25 A0 – 0,5 A
0 – 1500 V0 – 0,1 A0 – 0,2 A0 – 0,4 A
Output voltage / current — MX 1200W · 1500W · 2400W · 3000W
Output voltageMX 1200WMX 1500WMX 2400WMX 3000W
0 – 10 V0 – 120 A0 – 150 A0 – 240 A0 – 300 A
0 – 20 V0 – 60 A0 – 75 A0 – 120 A0 – 150 A
0 – 30 V0 – 40 A0 – 50 A0 – 80 A0 – 100 A
0 – 40 V0 – 30 A0 – 35 A0 – 60 A0 – 75 A
0 – 60 V0 – 20 A0 – 25 A0 – 40 A0 – 50 A
0 – 80 V0 – 15 A0 – 15 A0 – 30 A0 – 37,5 A
0 – 120 V0 – 10 A0 – 12 A0 – 20 A0 – 25 A
0 – 150 V0 – 8 A0 – 10 A0 – 16 A0 – 20 A
0 – 200 V0 – 6 A0 – 7,5 A0 – 12 A0 – 15 A
0 – 300 V0 – 4 A0 – 5 A0 – 8 A0 – 10 A
0 – 600 V0 – 2 A0 – 2,5 A0 – 4 A0 – 5 A
0 – 1200 V0 – 1 A0 – 1,25 A0 – 2 A0 – 2,5 A
0 – 1500 V0 – 0,8 A0 – 1 A0 – 1,5 A0 – 2 A

The maximum current shown depends on the voltage rating selected. MX 4000W / 5000W / 6000W ratings (400 Vac 3-phase): output voltage and current on request. Non-contractual data, subject to change.

Configuration

Options & accessories

Configure this product to match your process: control, metering and specific options. Three families of options, which can be combined to suit your application.

Interface

Control Panel

  • Manual voltage / current preset (U/I)
  • 7-segment LED displays
  • Real-time display
Touchscreen

Micronics Touch Control (MTC)

  • Touchscreen interface, built-in functions
  • Real-time I and U curves
  • Logs saved to USB stick
  • 5.7″ TFT LCD display, 262,000 colours

Panel PC

  • Touchscreen interface
  • Real-time I and U curves
  • Profile editor (ramps)
  • On / Off switch
Mounting
Remote, for cabinet integration
Remote, in an enclosure
On the front panel
Setpoint signal

Analogue

  • 0 – 10 V
  • 4 – 20 mA
  • Inputs and outputs isolated to 1500 Vrms

Digital

  • Ethernet
  • Profibus DP / PROFINET
  • 2-wire RS-485
  • Wi‑Fi
Depending on the level of control required
Active

Active meter

  • Preset counter
  • Electronic timer
Passive

Passive meter

  • Totaliser
  • Daily counter (A·h)
To be combined to suit your application

Polarity reverser

Reverses the direction of the current in the circuit — a real asset when starting up your bath.

Dual range

Optimal accuracy across two orders of magnitude, to cope with varying currents.

Sense leads

Regulation measured at the load terminals: compensates for the voltage drop in the power cables.

Ramp & timer

Voltage or current ramp-up, plus a cycle timer for controlled start-ups.

Innovation

TWIN

Dual-output rectifier: balanced current sharing from a single setpoint, with simplified wiring.

See all options in detail → Configure my rectifier
Applications

Where is the Microlab used?

Wherever a piece of equipment needs a clean, stable and adjustable DC source — one that does not drift over the hours.

Test bench

Powering a test bench and monitoring how equipment behaves over time.

See the page →

Laboratory & R&D

Characterising a component, powering a prototype, reproducing an operating condition.

Discuss my requirement →

Control & measurement

A stable, accurate source — the condition for repeatable measurements from one test to the next.

Discuss my requirement →

Prototyping & pre-production

Validating a solution on a small scale before moving up to workshop scale.

See the catalogue →

Worth remembering: a regulated power supply does not run your test — it provides the DC source the test relies on. Its stability directly determines how repeatable your measurements are.

How it works

How does a rectifier work?

Four steps between your workshop mains supply and your installation.

01

The mains supply, in AC

Your installation is fed by the mains network, in alternating current. A component or a test bench under test, however, needs direct current.

02

Conversion

The rectifier turns that alternating current into direct current, the only form your application can use.

03

Regulation

You set a voltage or current setpoint. The electronics hold it continuously, despite variations in the load and in the mains supply.

04

Output to your installation

The regulated direct current goes out to your equipment. Continuous measurement compares the result with the setpoint and corrects any deviation immediately.

Support

From your requirement to maintenance

A rectifier is rarely bought off the shelf: it is selected, configured, installed and maintained.

01

We start from your application

Process, voltage, current, environment, installation constraints: the right rectifier is chosen from your actual requirement.

Describe my requirement →02

Configuration & manufacturing

Control, metering, interfaces: your rectifier is configured for your installation, then assembled in our workshops in Villette-d'Anthon.

See the options →03

On-site commissioning

Our technicians come on site for the connection, the settings and the handover to your teams.

On-site service →04

Maintenance & genuine parts

Servicing, repair, genuine parts: your equipment stays operational year after year.

Repair & maintenance →
A question about your installation?After-sales and engineering department on 04 72 93 04 80 — Monday to Friday, 8 am–5 pm.
All our services
Custom requirement

A specific configuration?

Our teams design solutions to match your power and environmental constraints.